Concrete Resurrection Polyaspartic is the ultimate solution for elevating the appearance and longevity of concrete, natural stone, and other cementitious surfaces. Engineered for exceptional performance, this innovative coating delivers a remarkably high gloss shine that not only enhances aesthetic appeal but also provides robust protection against harsh environmental conditions, including UV rays, freeze/thaw cycles, and hot tire pick-up.
What sets Polyaspartic apart is its quick curing capability, allowing for foot traffic within 3-4 hours and the ability to recoat in just 2-3 hours, all while achieving full cure within 24 hours. This efficiency means less downtime and more opportunities to maximize profit. The superior penetration and bonding strength ensure that it holds tight to the surface, resulting in fewer callbacks, making it a reliable choice for professionals.
Each kit covers an impressive 200-600 square feet and features crystal-clear, high-gloss results without the risk of blushing from moisture. Notably, this coating exhibits exceptional stain resistance, effectively repelling chemicals, oils, and other contaminants while offering unparalleled abrasion, impact, and wear resistance that surpasses traditional epoxy or urethane options.
The user-friendly two-component system simplifies the mixing process, and it can be applied conveniently at temperatures ranging from 40°F to 85°F. With a film build of up to 6 mil, the surface protection increases significantly, providing additional peace of mind. Whether for interior or exterior projects, Concrete Resurrection Polyaspartic adapts effortlessly, ensuring flexibility in scheduling.
As a high-quality product with 80% solids and only 250 g/l VOCs, it combines performance with environmental consciousness. However, safety precautions must be noted as the product is flammable. Upgrade your surfaces with confidence using Concrete Resurrection Polyaspartic, where durability meets sophistication.
Caution: Concrete Resurrection Polyaspartic is flammable and susceptible to ignition. See TDS for Precautions and Limitations.
Click Here for PDF of Technical Data Sheet
Technical Data
Technical Data Sheet (TDS) CR-535
Polyaspartic Aliphatic Polyurea
**This product may only be used on fully cured concrete. Allow a minimum of 28-45 days of cure time after
the concrete is poured to allow ample time for the concrete to completely hydrate. It is recommended that a
calcium chloride (or similar) moisture test be completed on any floor prior to application.
PRODUCT
Polyaspartic provides a high gloss clear coating, which is extremely durable and has a very rapid cure time..
Can be used for most types of applications over properly prepared surfaces. It has superior penetration and
bonding strength, which can provide years of abrasion, impact, and wear resistance. It is resistant to
chemical splash and spills as well as hot tire pick up.
APPROXIAMATE COVERAGE RATES
Theoretical Coverage @ 80% Solids (Volume) per gallon
DFT........................................................1,283 ft. @ 1 mils
DFT...........................................................641 ft. @ 2 mils
DFT...........................................................428 ft. @ 3 mills
DFT........................................................... 320 ft. @ 4 mils
DFT.............................................................257 ft. @ 5 mills
DFT.............................................................213 ft. @ 6 mills
Coverage rates depend upon many conditions including application method,
surface porosity and applicator.
TECHNICAL INFORMATION
Solids.................................................................80%
Pot Life...................................................25-30 minutes
Re-Coat Time................................................2-3 hours
Foot Traffic.............................................................3-4 hours
Wheel Traffic.................................24 hours (recommended)
Application Temp...............................................40°F-85°F
Wet Appearance................................................................Clear
Dry Appearance................................Clear and Very High Gloss
VOC Content.................................................................<250 g/l
Blush Resistance.........................................................Excellent
Solvent Resistance......................................................Excellent
Concrete Adhesion......................................................Excellent
Meets USDA/CFSAN, U.S. Food Code, physical facilities criteria as outlined in 6.100.11 Surface
Characteristics USDA acceptable. Not intended for 21 CFR food contact.
***Please note that low air and/or concrete temperatures and/or relative humidity may extend drying
times. Follow recommended coverage rates for best results.
PROPERTY PROFILE
Tensile Strength: ASTM D 638: 4,500 to 5,000 psi
Mandrel Bend ASTM D 522: Passes, no cracking, 1/8” mandrel bend
Falling Sand Abrasion Resistance ASTM D 968:
Clear...30 liters sand/ 1 dry mil
SHELF LIFE
Up to 12 months in its original, sealed, unopened containers.
INSTRUCTIONS FOR USE
SURFACE PREPARATION: The concrete surface must be deemed mechanically and structurally sound,
completely clean, and dry. To achieve the above desired results, a mechanical grinding method should be
performed to an approximate 50-100 grit profile to insure flatness of the substrate, to remove surface
impurities, and to profile the surface of the floor to aCSP-2, as recommended by the ICRI Technical Guideline
No. 03732. If mechanical means of preparation are not suitable, it is recommended to prepare the surface
with Concrete Resurrection Surface Prep and Etch solution. The final rinse must contain a neutralizing
agent.
MIXING: Proper mixing is pertinent to application success. In equal parts (1:1), mix Part A and Part B using a
clean, dry mixing container. Stir contents approximately 30-60 seconds. Avoid over-mixing or creating a
vortex which could introduce moisture content to the mixture. No induction time is required prior to use, nor
after mixing. If integrating anti-skid media agents, only do so after Parts A & B have been thoroughly mixed.
POT LIFE: Expected workable pot life after mixing Part A and Part B is approximately 25-30 minutes at a
common temperature range of 70 F-80 F at roughly 50% relative humidity. Higher temperatures and high
percentages of humidity will shorten pot life, as colder temperatures and lower percentages of humidity will
extend the coatings pot life.
APPLICATION INSTRUCTIONS: Application should be completed using a 3/8” synthetic nap, phenolic core
roller, or a lambs’ wool cover for pigmented, stained floors, or media coats. Use a foam squeegee and back roll
with the roller over media floors (quartz or chips). Please note that the use of pump-up style spray bottle may
create visible bubbles, blisters, and pinholes and is not recommended.
CLEAN-UP
Use Xylene. Dispose of containers in accordance with local and federal regulations.
PRODUCT REMOVAL
Dried, cured polyaspartic may be removed by using a diamond grinding method, sandblasting method or
similar mechanical action.
PRECAUTIONS AND LIMITATIONS
►Will not freeze during storage, however, allow temperature to rise to 50 degrees F prior to application.
►All HVAC ventilation ducts should be blocked prior to application so solvents fumes are not distributed.
►Keep away from open flames and other ignition sources. Polyaspartic is flammable and is susceptible to
ignition.
►It is not recommended to apply to any floor without recommended preparation.
►Please be aware that this product when cured may be slippery when wet.
►May darken the surface of many new and existing concrete slabs. Test prior to use.
SPECIAL NOTES
Please consult Material Safety Data Sheet (MSDS) and read Warranty information prior to use.
Safety
Always use appropriate safety equipment including but not limited to, goggles, face shield, rubber gloves,
chemical resistant clothing or apron, and chemical respirator. For exterior use only.
INHALATION: Vapors may cause dizziness, headaches, or nausea. Immediately move to fresh air. Seek
medical attention.
EYES: Contact with eyes can cause severe burning, irritation, and blurred vision. Flush with water. Seek
medical attention.
SKIN: May cause severe irritation and or chemical burns. Wash with soap and water. Seek medical attention.
Keep out of reach of children. Use only with adequate ventilation.
Keep away from heat, sparks & flame. Vapors may cause fire. Avoid prolonged contact with skin. Use only
with adequate ventilation. Avoid breathing vapors or spray mist. Do not take internally. If swallowed, do not
induce vomiting. Call physician immediately. Close container after use.
It is the sole responsibility of the property owner or applicator to determine the suitability and safety of
applying this product in areas of pedestrian traffic.
Warranty
The Manufacturer and/or the Seller warrants that if any goods supplied prove defective in workmanship or
material, that Manufacturer and/or Seller shall replace them or refund the purchase price. This warranty is
made in lieu of any and all other warranties expressed or implied. Before application, the User shall determine
the suitability of the product for his intended use and User assumes all risks and liabilities whatsoever in
connection therewith. Under no circumstances shall the Manufacturer and/or Seller be liable for incidental,
consequential or other damages for alleged negligence, breach of warranty, or strict liability arising out of use
or handling of this product. The sole liability of Manufacturer and/or Seller for any claims arising out of the
use or sale of the product shall be for the User's purchase price. Any claim of defective product must be
received in writing within one (1) year from date of shipment.
Slip and Fall Precautions
OSHA and the American Disabilities Act (ADA) have standards for slip-resistance on pedestrian surfaces. The
coefficient of friction required by ADA is .6 on level surfaces and .8 on ramps. Engrave-A-Crete
recommends the use of slip-resistant additives in all sealers or coatings that may be exposed to wet, oily or
greasy conditions. It is the installer and end users' responsibility to provide a flooring system that meets
current safety standards. Engrave-A-Crete or its sales agents will not be responsible for injury
incurred in a slip and fall accident.